Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® T KR 4355 G5 LS sw 23189 - PA6T/6-GF25 - BASF

Material Data Center offers the following functions for Ultramid® T KR 4355 G5 LS sw 23189:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultramid T datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - 材料特有の特性
Any use of this information falls under the rules of our disclaimer.
商品の説明文
Glass fibre reinforced partially aromatic polyamide for injection moulding. High toughness, stiffness and strength, low water absorption, high melting point (295 °C), good laser markability.
Processing/Physical Characteristics乾燥/調湿単位テスト基準
ISO データ
成形収縮率, 平行 0.5 / * % ISO 294-4, 2577
成形収縮率, 直角 1.0 / * % ISO 294-4, 2577
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 9000 / 9000 MPa ISO 527
破壊応力 185 / - MPa ISO 527
破壊ひずみ 3 / - % ISO 527
引張クリープ弾性率, 1000h * / 6500 MPa ISO 899-1
シャルピー衝撃強さ, +23°C 80 / - kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 11 / - kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10°C/min 295 / * °C ISO 11357-1/-3
ガラス転移点, 10°C/min 105 / * °C ISO 11357-1/-2
荷重たわみ温度, 1.80 MPa 245 / * °C ISO 75-1/-2
ビカット軟化温度, B 285 / * °C ISO 306
線膨張係数, 平行 25 / * E-6/K ISO 11359-1/-2
線膨張係数, 直角 55 / * E-6/K ISO 11359-1/-2
1.5mm厚さでの燃焼性 HB / * class IEC 60695-11-10
試験片の厚さ 1.6 / * mm -
Yellow Card 可用 はい / * - -
厚さhでの燃焼性 HB / * class IEC 60695-11-10
試験片の厚さ 0.8 / * mm -
Yellow Card 可用 はい / * - -
酸素指数 24 / * % ISO 4589-1/-2
電気的特性.乾燥/調湿単位テスト基準
ISO データ
比誘電率, 1MHz 4.3 / 4.5 - IEC 62631-2-1
誘電正接, 1MHz 300 / 400 E-4 IEC 62631-2-1
体積抵抗率 1E13 / 1E12 Ohm*m IEC 62631-3-1
表面抵抗率 * / 1E13 Ohm IEC 62631-3-2
耐電圧 33 / 31 kV/mm IEC 60243-1
耐トラッキング性 - / 600 - IEC 60112
その他の特性.乾燥/調湿単位テスト基準
吸水率 5.5 / * % Sim. to ISO 62
吸湿率 1.3 / * % Sim. to ISO 62
密度 1350 / - kg/m³ ISO 1183
材料特有の特性乾燥/調湿単位テスト基準
ISO データ
粘度数 130 / * cm³/g ISO 307, 1157, 1628
特殊な特性
成形加工法.
射出成形.
納入形状.
ペレット., 黒
添加剤.
離型剤.
特殊な特性.
熱安定化.
な特性
Laser Markable
領域別の利用可能性
ヨーロッパ.
その他の情報
村遜速揃
PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 110 °C
Pre/Post-processing, Pre-drying, Time: 8 h

PROCESSING
injection molding, Melt temperature, range: 310 - 330 °C
injection molding, Melt temperature, recommended: 320 °C
injection molding, Mold temperature, range: 80 - 120 °C
injection molding, Mold temperature, recommended: 100 °C
injection molding, Dwell time, thermoplastics: 5 min
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.